Terminal accommodating chamber Yasmin live chat

Posted by / 21-Jun-2019 23:29

Terminal accommodating chamber

(1) This Part applies in respect of a vessel that is constructed, manufactured or rebuilt in, or imported into, Canada in order to be sold or operated in Canada and that is 701.

Unless otherwise indicated in these Regulations, the builder, manufacturer, rebuilder, importer and owner of a vessel shall ensure that the vessel meets the requirements of this Part. A pleasure craft shall meet Information Note: Existing Pleasure Craft: Existing pleasure craft that were constructed according to an earlier version of this Standard are not required by the Regulations to comply with the current construction requirements of the with respect to non-pleasure craft versus pleasure craft is identified at the beginning of each section under the subsection titled "Scope." Construction Requirements: The Construction Requirements consist of the requirements of Part 7 of the are not part of the Construction Requirements, therefore any reference to the requirements of Part 4 and Part 5 in this Standard are provided for information and are not mandatory for the builder, manufacturer, rebuilder or importer to meet the Construction Requirements as stated in a Declaration of Conformity.

Where standards from other organizations are referenced, they may be obtained from the addresses listed (see "Referenced Organizations").

The conversions shown in this Standard have been done using a "soft" conversion method or rounded to the nearest millimetre.

(3) In this section, “major modification” means a modification or repair or a series of modifications or repairs that substantially changes the capacity or size of a vessel or the nature of a system on board a vessel, that affects its watertight integrity or its stability, or, except in the case of the restoration of an antique wooden pleasure craft, that substantially increases its service life. (1) If it is necessary, because of the type or design of a vessel other than a pleasure craft, to obtain information in order to establish the vessel's compliance with the construction requirements, the builder, manufacturer, rebuilder, importer or owner of the vessel shall submit to the Minister, on request, the following documents: (2) If a vessel, other than a pleasure craft, was constructed, manufactured or rebuilt before the day on which these Regulations came into force, the owner of the vessel may submit photographs and technical data instead of the documents referred to in subsection (1). Every safety notice required under this Part shall As stated by the Regulations: 900.

(1) This Part applies in respect of a vessel that is constructed, manufactured, rebuilt or imported in order to be sold or operated in Canada.

() Monohull Powerboat with Add-on Swim Platform Monohull Powerboat with Built-in Swim Platform Fin Keel Sailboat Full Keel Sailboat Multihull/Pontoon Inflatable/Rigid Inflatable Information Note: Application of this Standard - As stated by the Regulations: 700.

These provisions could be made standard equipment on all vessels or be offered as an option to the end user. A pleasure craft that is 24 or more in length shall be constructed, manufactured or rebuilt in accordance with the applicable recommended practices and standards in force on its date of construction, manufacture or rebuilding. (4) A provision in the American Boat and Yacht Council standards referred to in these Regulations that is expressed as a recommendation shall be read as a requirement unless it is incompatible with the vessel's construction.

(5) Except as otherwise indicated in these Regulations, any reference in these Regulations to a document is a reference to that document as amended from time to time. If the design of a type of vessel or of a system or component of a vessel would render it unsafe, unsuitable or impracticable to construct, manufacture or rebuild the vessel in accordance with the construction requirements, the vessel may be constructed, manufactured or rebuilt according to the recommended practices and standards that provide a level of safety at least equivalent to that provided by the construction requirements and that are applicable to the construction, manufacture or rebuilding of a vessel of that design, for example, As stated by the Regulations: 710.

Responsible Authority: The Director, Design, Equipment and Boating Safety, is responsible for this document, including any change, correction, or update.

Approval: Victor Santos-Pedro Director, Design, Equipment and Boating Safety, Marine Safety Original Date Issued: Date Revised: © Her Majesty the Queen in Right of Canada, as represented by the Minister of Transport, 2004.

terminal accommodating chamber-15terminal accommodating chamber-75terminal accommodating chamber-48

Information Note: The following definitions are taken from the .